entering activation code for mobility pack

$(UHello everyone

when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed that our installed mobility pack had no active registration.

So i wondered where to enter the activation code.

I ended up doing it with "suse_register -a regcode-mobility=".

But i guess there must be a non command-line (=GUI) possibility.

YAST / NCC did not work as you can enter only the activation code for SLES 11.

Someone has some insights on this?

Thanks
Andrej
  • On 13/03/2013 13:35, Andrej Dimic wrote:

    > when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed
    > that our installed mobility pack had no active registration.
    >
    > So i wondered where to enter the activation code.
    >
    > I ended up doing it with "suse_register -a regcode-mobility=".
    >
    > But i guess there must be a non command-line (=GUI) possibility.
    >
    > YAST / NCC did not work as you can enter only the activation code for
    > SLES 11.
    >
    > Someone has some insights on this?


    During (or after) installation you can also enter the Customer Center
    Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
    the Mobility Pack Installation Guide @
    http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

    HTH.
    --
    Simon
    Novell/SUSE/NetIQ Knowledge Partner

    ------------------------------------------------------------------------
    Do you work with Novell technologies at a university, college or school?
    If so, your campus could benefit from joining the Novell Technology
    Transfer Partner (TTP) program. See novell.com/ttp for more details.
    ------------------------------------------------------------------------
  • >>During (or after) installation you can also enter the Customer Center

    >>Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
    >>the Mobility Pack Installation Guide @
    >>http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

    Hm, but this is for a new install.

    I was talking about an upgrade from 1.2.4 to 1.2.5.

    Again, i find that i can enter the activation code for SLES 11 in NCC but not for Data Synchronizer.

    Thanks
    Andrej




    >>> Simon Flood<smflood@no-mx.forums.novell.com> 13.03.2013 16:12 >>>

    On 13/03/2013 13:35, Andrej Dimic wrote:


    > when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed
    > that our installed mobility pack had no active registration.
    >
    > So i wondered where to enter the activation code.
    >
    > I ended up doing it with "suse_register -a regcode-mobility=".
    >
    > But i guess there must be a non command-line (=GUI) possibility.
    >
    > YAST / NCC did not work as you can enter only the activation code for
    > SLES 11.
    >
    > Someone has some insights on this?


    During (or after) installation you can also enter the Customer Center
    Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
    the Mobility Pack Installation Guide @
    http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

    HTH.
    --
    Simon
    Novell/SUSE/NetIQ Knowledge Partner

    ------------------------------------------------------------------------
    Do you work with Novell technologies at a university, college or school?
    If so, your campus could benefit from joining the Novell Technology
    Transfer Partner (TTP) program. See novell.com/ttp for more details.
    ------------------------------------------------------------------------