Highlighted
Absent Member.
Absent Member.
603 views

entering activation code for mobility pack

$(UHello everyone

when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed that our installed mobility pack had no active registration.

So i wondered where to enter the activation code.

I ended up doing it with "suse_register -a regcode-mobility=".

But i guess there must be a non command-line (=GUI) possibility.

YAST / NCC did not work as you can enter only the activation code for SLES 11.

Someone has some insights on this?

Thanks
Andrej
Labels (1)
0 Likes
2 Replies
Highlighted
Knowledge Partner
Knowledge Partner

Re: entering activation code for mobility pack

On 13/03/2013 13:35, Andrej Dimic wrote:

> when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed
> that our installed mobility pack had no active registration.
>
> So i wondered where to enter the activation code.
>
> I ended up doing it with "suse_register -a regcode-mobility=".
>
> But i guess there must be a non command-line (=GUI) possibility.
>
> YAST / NCC did not work as you can enter only the activation code for
> SLES 11.
>
> Someone has some insights on this?


During (or after) installation you can also enter the Customer Center
Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
the Mobility Pack Installation Guide @
http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

HTH.
--
Simon
Novell/SUSE/NetIQ Knowledge Partner

------------------------------------------------------------------------
Do you work with Novell technologies at a university, college or school?
If so, your campus could benefit from joining the Novell Technology
Transfer Partner (TTP) program. See novell.com/ttp for more details.
------------------------------------------------------------------------
0 Likes
Highlighted
Absent Member.
Absent Member.

Antw: Re: entering activation code for mobility pack

>>During (or after) installation you can also enter the Customer Center

>>Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
>>the Mobility Pack Installation Guide @
>>http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

Hm, but this is for a new install.

I was talking about an upgrade from 1.2.4 to 1.2.5.

Again, i find that i can enter the activation code for SLES 11 in NCC but not for Data Synchronizer.

Thanks
Andrej




>>> Simon Flood<smflood@no-mx.forums.novell.com> 13.03.2013 16:12 >>>

On 13/03/2013 13:35, Andrej Dimic wrote:


> when upgrading from DS 1.2.4 to 1.2.5, the patch update wizard claimed
> that our installed mobility pack had no active registration.
>
> So i wondered where to enter the activation code.
>
> I ended up doing it with "suse_register -a regcode-mobility=".
>
> But i guess there must be a non command-line (=GUI) possibility.
>
> YAST / NCC did not work as you can enter only the activation code for
> SLES 11.
>
> Someone has some insights on this?


During (or after) installation you can also enter the Customer Center
Activation Code through the YaST GUI - see step 11 in section 2.3.2 of
the Mobility Pack Installation Guide @
http://www.novell.com/documentation/datasynchronizer1/datasync125_install_mobility/data/bmzom7o.html#bn0ufpd

HTH.
--
Simon
Novell/SUSE/NetIQ Knowledge Partner

------------------------------------------------------------------------
Do you work with Novell technologies at a university, college or school?
If so, your campus could benefit from joining the Novell Technology
Transfer Partner (TTP) program. See novell.com/ttp for more details.
------------------------------------------------------------------------
0 Likes
The opinions expressed above are the personal opinions of the authors, not of Micro Focus. By using this site, you accept the Terms of Use and Rules of Participation. Certain versions of content ("Material") accessible here may contain branding from Hewlett-Packard Company (now HP Inc.) and Hewlett Packard Enterprise Company. As of September 1, 2017, the Material is now offered by Micro Focus, a separately owned and operated company. Any reference to the HP and Hewlett Packard Enterprise/HPE marks is historical in nature, and the HP and Hewlett Packard Enterprise/HPE marks are the property of their respective owners.