Valued Contributor.. OnaBrink Valued Contributor..
Valued Contributor..
501 views

Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

I have recently upgraded our SM 9.50 system and the application server was originally configured for software vertical load blancing. I want to configure 2 application servers at 2 different locations using a spanned vlan and VIP on an HWLB (citrix netscaler) with 300 concurrent connections each. SM 9.6x documentation supports this for an F5, but it is not clearly explained. The documentation even has 2 great diagrams, but no detail. The documentation also states that if using an HWLB, you cannot use software load balancing. How could I get 300 concurrent connections if the max for a single servlet is 100.  This means I would need multiple vm servers instead of using servlets. I still wonder where and how the license file is referenced. If the license file is sitting on one server and only referenced on one server, that server is a single point of failure. This means Service Manager cannot ever be configured for high availability. If that one host goes down, no other connections can be made, which also means users connected to that host are dropped and can't be regained. Has anyone done this and if so, how? Samples of an SM.ini and SM.cfg file would be helpful as well.

1 Solution

Accepted Solutions
Super Contributor.. Madddy Super Contributor..
Super Contributor..

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

you can generate license on any server, even if the server(license IP) fails, your application will be running. License IT is considered only during the start up.

you can test the same

View solution in original post

0 Likes
6 Replies
BAGAss Super Contributor.
Super Contributor.

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

there are two scalable methods
vertical (on one server)
and
horizontal (on some servers)
which one do u interesting?

Valued Contributor.. OnaBrink Valued Contributor..
Valued Contributor..

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

I am not referring to the software load balancing that is part of SM. I am referring to using a hardware load balancer to horizontally load balance the application server and support high availability.

Micro Focus Expert
Micro Focus Expert

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution
Valued Contributor.. OnaBrink Valued Contributor..
Valued Contributor..

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

Thank you. I have seen and read the documentation supplied by Micro Focus, but it does not explain where the license file resides or how it is referenced by the license manager.

If the license manager resides on a single node as in a software load balancer and that node fails, it would still be a single point of failure. Especially, since the license is locked to a single IP. If that is true, it doesn't really matter if an HWLB is used or not. One purpose of an HWLB is to have high availaibility and resiliency. Can someone explain how to obtain high availailability with SM application servers?

Contributor.. kchamberlin Contributor..
Contributor..

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

Hi,  I'm looking for the same information as I'm about to attempt the HWLB configuration as well.  I'm  particularly interested in the scaling on each individual App server if SWLB isnt supported vertically.  Have you made any progress with this.  Documentation is Lacking to say the least!

Super Contributor.. Madddy Super Contributor..
Super Contributor..

Re: Can someone explain how to set up multiple SM 9.6x application servers to use an HWLB

Jump to solution

you can generate license on any server, even if the server(license IP) fails, your application will be running. License IT is considered only during the start up.

you can test the same

View solution in original post

0 Likes
The opinions expressed above are the personal opinions of the authors, not of Micro Focus. By using this site, you accept the Terms of Use and Rules of Participation. Certain versions of content ("Material") accessible here may contain branding from Hewlett-Packard Company (now HP Inc.) and Hewlett Packard Enterprise Company. As of September 1, 2017, the Material is now offered by Micro Focus, a separately owned and operated company. Any reference to the HP and Hewlett Packard Enterprise/HPE marks is historical in nature, and the HP and Hewlett Packard Enterprise/HPE marks are the property of their respective owners.