farmeunitWPSD

Absent Member.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
2013-12-23
18:06
1149 views
Changing IP Subnet
I know there is TID 7013382(Support | How to change the IP address of the iPrint Appliance) for changing IP information, but if I'm only changing the subnet, does this still apply?
I haven't really done much work in iPrint besides getting it installed, just wanted to make sure before I get going on it. I planned on working on it a lot this week. The subnet/VLAN thing is a little new to me as far as making things work.
I haven't really done much work in iPrint besides getting it installed, just wanted to make sure before I get going on it. I planned on working on it a lot this week. The subnet/VLAN thing is a little new to me as far as making things work.
4 Replies
smflood

Fleet Admiral
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
2013-12-23
23:36
farmeunitWPSD Wrote in message:
> I know there is TID 7013382('Support | How to change the IP address of
> the iPrint Appliance'
> (http://www.novell.com/support/kb/doc.php?id=7013382)) for changing IP
> information, but if I'm only changing the subnet, does this still
> apply?
>
> I haven't really done much work in iPrint besides getting it installed,
> just wanted to make sure before I get going on it. I planned on working
> on it a lot this week. The subnet/VLAN thing is a little new to me as
> far as making things work.
So you're not changing the IP address but just the network mask?
If so, you should be able to just change the latter by logging
into the iPrint Appliance via SSH and then running YaST (command
is all lowercase "yast") - with Appliance 1.0.1 you can't change
the network configuration via web-based Management Console (as
per note in section 8.2 of Administration Guide[1]).
I'd reboot the Appliance after changing.
HTH.
[1] https://www.novell.com/documentation/iprint-
appliance1/iprint_appliance/data/network.html (URL may
wrap)
--
Simon
Novell Knowledge Partner
----Android NewsGroup Reader----
http://www.piaohong.tk/newsgroup
> I know there is TID 7013382('Support | How to change the IP address of
> the iPrint Appliance'
> (http://www.novell.com/support/kb/doc.php?id=7013382)) for changing IP
> information, but if I'm only changing the subnet, does this still
> apply?
>
> I haven't really done much work in iPrint besides getting it installed,
> just wanted to make sure before I get going on it. I planned on working
> on it a lot this week. The subnet/VLAN thing is a little new to me as
> far as making things work.
So you're not changing the IP address but just the network mask?
If so, you should be able to just change the latter by logging
into the iPrint Appliance via SSH and then running YaST (command
is all lowercase "yast") - with Appliance 1.0.1 you can't change
the network configuration via web-based Management Console (as
per note in section 8.2 of Administration Guide[1]).
I'd reboot the Appliance after changing.
HTH.
[1] https://www.novell.com/documentation/iprint-
appliance1/iprint_appliance/data/network.html (URL may
wrap)
--
Simon
Novell Knowledge Partner
----Android NewsGroup Reader----
http://www.piaohong.tk/newsgroup
farmeunitWPSD

Absent Member.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
2013-12-24
02:55
Yes, just changing subnets. We're on flat networks right now, but moving to VLANs as we're expanding greatly over the next few months and we're already around 500 devices on network.
Thanks, Simon. I'll give it shot.
Thanks, Simon. I'll give it shot.
farmeunitWPSD

Absent Member.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
2013-12-24
17:23
Quick question, also. I made a thread about this in the Filr forum, but I'm assuming it's the same process for the Filr Appliance?
smflood

Fleet Admiral
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
2013-12-24
19:43
farmeunitWPSD Wrote in message:
> Quick question, also. I made a thread about this in the Filr forum, but
> I'm assuming it's the same process for the Filr Appliance?
I've answered your other thread but you should be okay just
changing network mask.
HTH.
--
Simon
Novell Knowledge Partner
----Android NewsGroup Reader----
http://www.piaohong.tk/newsgroup
> Quick question, also. I made a thread about this in the Filr forum, but
> I'm assuming it's the same process for the Filr Appliance?
I've answered your other thread but you should be okay just
changing network mask.
HTH.
--
Simon
Novell Knowledge Partner
----Android NewsGroup Reader----
http://www.piaohong.tk/newsgroup